Caterham Seven User Manual Page 155
- Page / 227
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page | 154
The carpet must fit flat at the transmission
tunnel. If necessary, small cuts should be
made in the area of the corners to allow
the tabs on the carpet to hinge out against
the transmission tunnel.
Once the carpet has been fitted around
the transmission tunnel apply adhesive to
the carpet and press into position against
the seat back. It is only necessary to
apply adhesive as far down as the top of
the transmission tunnel as the remainder
of the carpet is behind the seats.
10.3) Transmission tunnel carpet
Attach the small aluminium transmission
tunnel cover on the rear of the
transmission tunnel top using the 5/32"
rivets provided.
Ensure that the reverse light switch and
associated blanking grommet have been
installed prior to fitting the transmission
tunnel carpets. The transmission tunnel
carpets are handed so ensure that the
correct carpet is fitted to each side.
Coat the transmission tunnel with
adhesive and stick the transmission tunnel
carpets to the transmission tunnel.
Ensure that good adhesive coverage is
maintained, particularly in the forward
section of the transmission tunnel.
10.4) Transmission tunnel top
NOTE
Do not attempt to fit the tunnel top until
the tunnel carpet adhesive is completely
dry.
The transmission tunnel top incorporates
a padded armrest, the gear lever gaiter
and the handbrake gaiter. On R300/R400
models the two electrical plugs on the
underside of the tunnel top must be
connected to the two plugs in the
transmission tunnel.
Pull the handbrake near vertical. Fit the
transmission tunnel top, ensuring that the
handbrake and gear lever locate in the
respective gaiter and press firmly into
position over the sides of the transmission
tunnel carpets.
Screw the gear knob into position and lock
with a grubscrew.
10.5) Rubber footwell mats
Place the mats in the respective footwell
(mats are handed).
They are secured into the footwell using
the three poppers fitted at the rear of the
footwell.
Attach 3 popper bases (fastener pack
ZIT03 Item 2) to the rear of the front
footwell using rivets (1) through which
need to be drilled in the floor panel.
- ASSEMBLY GUIDE 1
- ALL CATERHAM SEVEN MODELS 1
- Version 02.2014 1
- Contents 2
- List of Tables 11
- List of Figures 12
- Page 13
- Page 14
- Page 15
- Page 16
- 1.0) Introduction 20
- 2.0) Kit contents 28
- Exhaust silencer 29
- Exhaust primary pipes 29
- Cat/ collector 29
- Cat guard 29
- Polythene bag 29
- 1. RH driveshaft 33
- 4. Nyloc nut (white insert) 33
- 2. Speed sensor ring 33
- 5. LH driveshaft assembly 33
- 3. Nyloc nut (green insert) 33
- 1. LH headlight bracket 38
- 2. RH headlight bracket 38
- 1. Upright assembly (RH) 39
- 2. Upright assembly (LH) 39
- 4.0) Steering 59
- 1. Steering wheel 63
- 4. Fixing screw 63
- 2. Steering column 63
- 5. Wheel centre 63
- 3. Mounting boss 63
- 5.0) Front suspension 65
- 1. Copper washer 71
- 3. Braided brake hose 71
- 2. Female union 71
- 4. Adaptor 71
- 1. Clutch release bearing 74
- 2. Hydraulic connection 74
- 1. Gearbox 74
- 2. Plug 74
- 3. Gearbox mounting 74
- SWL of 150 Kg 77
- 2. ‘U’ hose 78
- 3. Water rail 78
- 1. Fuel rail connection 83
- 2. Fuel pipe (from pump) 83
- 4. Bobbin 85
- 2. Spring washer 85
- 3. Setscrew 85
- 1. Primary pipe 86
- 1. Hose to ‘T’ piece 88
- 1. Cam cover 94
- 2. Breather pipe 94
- 3. Throttle body 94
- 1. Air intake 95
- 2. Trunking 95
- 1. Brake master cylinder 97
- 4. Heater control cable 97
- 2. Clutch master cylinder 97
- 5. Battery 97
- 3. Heater 97
- 1. Banjo bolt 104
- 3. Hose union 104
- 2. Copper washers 104
- 4. Clutch master 104
- 1. Angle bracket 105
- 2. Bobbin 105
- 1.Primary pipe 106
- 2.Collector/catalyst 106
- 1. Silencer bracket 107
- 3. Lambda probe 107
- 2. Band clamp 107
- 2. Bottom radiator hose 108
- 1. Cruciform 109
- 1. Scuttle panel 113
- 2. Heater control cable 113
- 3. Locknut 113
- 1. Heater valve 113
- 1. Throttle cable 114
- 2. Throttle cable adjuster 114
- 3. Throttle body linkage 114
- 4. Throttle cable nipple 114
- Description 117
- Engine hoist and sling 117
- SWL if 150 Kg (min) 117
- 1. Engine connection 118
- 2. Long ‘L’ hose 118
- 1. ‘T’ piece 131
- 3. Small straight hose 131
- 2. Hose to 131
- 4. Hose to heater outlet 131
- 1. Oil breather hose 135
- 2. ‘P’ clip 135
- 3. Breather bottle 135
- 4. Breather elbow 135
- 5. Cam cover 135
- 1. Cable bracket 137
- 9.0) Rear suspension 140
- 1. Brake pipe (RH) 141
- 4. Brake pipe (LH) 141
- 5. Di Dion ear (RH) 141
- 3. Three way union 141
- 1. P-clip 142
- 2. Brake pipe LH 142
- 3. Three way connector 142
- 1. Bell crank 143
- 2. Rod end 143
- 4. Link arm (forward) 143
- 5. Link arm (rearward) 143
- 1. De Dion tube RH end 144
- 2. Link arm (forward) 144
- 3. Bellcrank 144
- 4. Link arm (rearward) 144
- 5. Bellcrank spacer 144
- 1. Metalistic brush 145
- 4. Nylon washers 145
- 2. Bolt 145
- 5. Nyloc nut 145
- 3. ‘A’ frame 145
- 1. De Dion ear 148
- 2. ARB bracket 148
- 3. Anti-roll bar 148
- 4. Drive shaft 148
- 5. Speed sensor 148
- 1. Bolt 149
- 4. Drop link 149
- 2. Plain washer 149
- 5. Anti-roll bar 149
- 3. Extension piece 149
- 1. Pulley 151
- 10.0) Interior and trim 154
- 1. Knee trim panel 157
- 2. Roll cage (optional) 157
- 3. Piping 157
- 4. Self-tapping screws 157
- 1. Spacers 161
- 2. Adjusting handle 161
- 1. Composite seat 162
- 2. Six-point harness 162
- 3. Seat adjuster 162
- 1. Large recess 162
- 2. Spacer 162
- 1. Rear bulkhead carpet 164
- 2. Footwell carpet 164
- 3. Tunnel carpet 164
- 4. Tunnel top 164
- 11.0) Fibreglass 165
- 1. Rear wing fixings 168
- 2. Rear wings 168
- 3. Rectangular notches 169
- 1. Wing piping 169
- 2. ‘V’ Shaped notches 169
- 12.0) Lighting 170
- 13.0) Weather equipment 175
- 1. Screw 176
- 2. Washer (or popper base) 176
- 3. Hoodstrap 176
- 4. Rear body skin 176
- 5. Chassis tube 176
- 1. Hoodstick 177
- 2. Popper base 177
- 3. Rear wing 177
- 1. Windscreen stanchions 177
- 2. Sidescreen hinges 177
- 1. Sidescreen 179
- 2. Vinyl strap 179
- 1. Popper base 182
- 2. Boot cover 182
- 3. Fastener socket 182
- 1. Tonneau cover 183
- 1. Windscreen support 183
- 1. Punch 184
- 2. Dished base 184
- 14.0) Wheel fitment 185
- 1. Mounting wishbone 186
- 2. Wheel nuts 186
- 3. Fibre washer 186
- 4. Spare wheel bolt 186
- 5. Spacer 186
- 1. Pipe to master cylinder 189
- 2. Push-fit connector 189
- 3. Bleed key 189
- 1. Grommets 203
- Page 205
- 17.0) Options 206
- 1. Front hoop saddle bracket 209
- 3. Chassis top tube - sill 209
- 1. Bucket bush location 210
- 2. Roll cage rear hoop 210
- 3. Seat back harness rail 210
- 1. Speed sensor bracket 219
- 2. Lock nut 219
- 3. Speed sensor 219
- 18.0) Wiring diagrams 223
- Page 227
Related products and manuals for Cars Caterham Seven
Cars Caterham Seven User Manual
(134 pages)
(134 pages)
© 2020, manymanuals.com. All rights reserved. | 0.279 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals